opti-cap ? ultra broadband dc blocking improved x7r performance dielectric laboratories inc. 2777 route 20 east, cazenovia, ny 13035-9477 phone: 315-655-8710 facsimile: 315-655-0445 e-mail: sales@dilabs.com web: http://www.dilabs.com quality system iso 9001:1994 certified environmental system iso 14001:1996 certified 1 jun. 18, 03 opt i - ca p ? features benefits ultra broadband, low loss resonance free dc blocking to >40ghz 0602 mounting footprint surface mountable by solder or epoxy bonding very low series inductance x7r temperature and voltage stability available in tape & reel or waffle pack format improved low frequency stability over temperature opti-cap ? electrical characteristics part number (includes t&r) capacitance / mlc case size voltage rating temperature coefficient ir (@+20 c, rated voltage) max df 1khz aging rate (% per decade hour max.) term frequency range 3db pts. typical uses fp (ghz) maximum process temperature / recommended attachment method p02bn820ma2636 100 nf 20% / 0603 16 vdc x7r ? c max: 15% (-55oc to 125oc) 10 2 m ? 3.0% 1.0% au (flash) 16 khz. ? >>40 ghz sonet oc-768 oc-192 1.3 250 c/ conductive epoxy or solder replaces p02bj300kb1954t / 2337t, p02bj820mb1954t / 2337t, P02BJ820MB1891T / 2338t & p02bj820mc1954t physical characteristics 0.058 milli-ca p ?
dielectric laboratories inc. 2777 route 20 east, cazenovia, ny 13035-9477 phone: 315-655-8710 facsimile: 315-655-0445 e-mail: sales@dilabs.com web: http://www.dilabs.com quality system iso 9001:1994 certified environmental system iso 14001:1996 certified 2 jun. 18, 03 opti-ca p ? electrical performance mounting recommendations to achieve design performance : ? surface a of the milli-cap ? (see drawing on page 1) is to always be in direct contact with the circuit trace. ? reflections will be minimized wh en a 50 ohm microstrip line with a width of . 020? to .025?, (.508mm to .635mm) is used. ? a gap in the microstrip should be approxim ately .015? to .020?, (.381mm to .508mm) when mounting with conductive epoxy. ? a gap in the microstrip should be appr oximately .010? to .015?, (.254mm to .381mm) when mounting with solder. ? the maximum processing temperatures is +250 c. solder dams are suggested for solder attach process. ? objective is to maintain part sy mmetry in relationship to microstrip. consult factory for additional inform ation or special requirements. milli-cap ? and opti-cap ? are registered trademarks of dielectric laboratories dli reserves the right to make changes in product designs and or pricing. sales are subject to dli?s conditions of sale. dli has no control on conditions of use; no warranty is made or implie d as to suitability for customers? intended use. dli shall in no event be responsible for incidental or consequential damages in cluding, without limitation, personal injury or property damage. -4.5 -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 -45 -40 -35 -30 -25 -20 -15 -10 -5 0 5 0 5 10 15 20 25 30 35 40 opti-cap insertion & return loss, (s21 & s11) p02bn820ma2636 s21 (db) s11 (db) frequency (ghz) s21 s11 s11 s21 opti-cap low frequency insertion loss, (s21) p02bn820ma2636 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 0 102030405060708090100 frequency (khz) s21 (db)
|
